http://www.501thailand.com
สร้างเว็บไซต์Engine by iGetWeb.com

 HOME

 ABOUT US

 501st THAI MEMBER

 501st EVENT

 CONTACT US

สาธิตการประกอบชุดสตอม Assembly for the Armor

สาธิตการประกอบชุดสตอม Assembly for the Armor


Assembled Stormtrooper Photo and 501st Approval List.

     

Will show the assembled (completed) photo with the list of the 501st aprroval requirements.
Actually 2 additional, optional levels of costuming excellence in the page of Costume Reference Library, Stormtrooper, ANH Hero.
Requirements for Level 1 "Expert Infantryman", requirements for Level 2 "Centurion".
Please visit the website for a full description of these standards.
For 501st membership only the requirements is as below need to be met.

     

[Helmet]

     

     

For 501st approval:

* Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) are gray.
* Rear traps and tears have vertical black lines.
* Lenses may be flat or bubble, green or smoke, sufficiently dark enough to obscure the costumer's eyes.
* The “ear” bars may have three or four bumps and should be gray or painted gray, with a black outline. Painting the bumps with a rank stripe (highlighted) in black is optional.
* Frown is painted gray and does not leave the teeth area. Six total teeth on the frown are cut out and the frown is tapered at the ends.
* Tube stripes are medium blue, should be 11 or 13 per side but can be between 9 and 16 per side with the curve bends extending backwards.
* Vocoder (vertically ribbed chin detail) is painted black.
* Aerators/Hovi mix tips (cylinders on either side of the vocoder) are black or painted black.
* Tears, traps, and tube stripes may be hand painted, decals, or decals that replicate hand painted.
* Mesh may be used behind the frown to obscure the face of the wearer.
* Note: The FX helmet is considered deprecated (to be avoided), though is acceptable for Legion requirements.
* Note: A stock (out of the box) MRCE and/or EFX PCR helmet does not meet the basic 501st requirements without the major modification that are necessary. Please see FISD/whitearmor.net for more info on these modifications sa below.

     

Tutorial Stormtrooper Helmets

- have green or black bubble lenses (the color of the lenses is still debated as they appear dark on screen, but Mark Hamill / Luke refers to the lenses as being green.
- 3 teeth on each side of the face
- ear pieces have 2 screws on each ear
- hero ears have 3 ear bumps, generally with the rear most painted black
- the black brow / rubber trim is usually lower on the hero helmets
- most hero helmets were made of white ABS plastic
- all the details (traps, vents, teeth, tube stripes, etc.) were hand painted

     

     

[Armor]

1. Abdomen Armor
For 501st approval:
The abdomen armor has a button area that matches the color pattern shown (3 blue + 6 gray); buttons are approximately 7/16" (11mm) in diameter.

2. Kidney Armor
For 501st approval:
A separate kidney plate is present, split from the posterior armor.

3. Posterior Armor
For 501st approval:
A separate rear plate is required, split from the kidney plate.

4. Chest Armor
For 501st approval:
Chest plate overlaps the abdominal plate.

5. Back Armor
For 501st approval:
Back plate contains a "O II" design.

6. Shoulder Straps
For 501st approval:
These shall be securely mounted in front and may free float in back. They may be affixed with rivets, Velcro, or adhesive.

7. Shoulder Armor
For 501st approval:
One on each shoulder. The shoulder bells are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders and should have a black elastic strap that wraps around the inside of the bicep.

8. Upper Arm Armor
For 501st approval:
Biceps are fully closed.

9. Forearm Armor
For 501st approval:
Forearms are fully closed.

10. Lower Leg Armor
For 501st approval:
Greaves close in the back.
The trapezoid knee plate (sniper knee plate) is affixed to the left greave and may have two visible brads or rivets securing it to the greave.

11. Thigh Armor
For 501st approval:
Thigh armor shall be closed in the back.
The small ammo belt is installed on the bottom of the right thigh.

12. Belt
For 501st approval:
* Belt face is made of plastic (TK ammo belt).
* The soft belt proper is made of canvas, or material with a canvas covering. Size must be 2.75” (70 mm) to 3.25”(83 mm) wide and not wider than the plastic portion of the belt. The color is be white to off-white.
* The drop boxes dangle from the sides of the front plastic belt (ammo belt) via white straps and are aligned under the plastic tabs of the ammo belt.

13. Thermal Detonator
For 501st approval:
* (A.K.A. O2 canister) attaches to the center back of the belt.
* Detonator consists of an all grey cylinder, without silver stickers or silver paint.
* The cylinder is between 2” (50mm) and 2.68"(68mm) in diameter with white end caps on each end.
* The white control panel pad faces upwards, with the controls/round washer style detail closest to the right end cap.
* The total length is approximately 7.50" (190.5mm).
* The thermal detonator is attached via metal or metallic-appearing clips, approximately 1" (25mm) wide.

     

■ Velcro Setting Image

     

1. Shoulder Strap - Shoulder Armor - Upper Arm Armor

     

2. a) Chest Armor - Back Armor   b) Abdomen Armor - Kindney Armor   c) Abdomen Armor - Thigh Armor

     

*** Velcro Image

     

■ Other Reference

      

     

     

     

*** Reference and Special Thanks to : Costume Reference Library, Stormtrooper, ANH HeroTutorial Stormtrooper Helmets

view
view